To display the tracks the SCC unit needs about sec for calculation. If the display starts to flash press the selection button R once. Page Programming Short View 2. Spiele 2. Programming: Press according button - hold down - and press selection button R , release both buttons and enter the new value. Page Programming Of Time Functions Enter the correct year with two digits, then enter a 0 followed by the number of the weekday.
The changer starts an initialisation run. After this the jukebox is ready to use. Part number of this switch is Page 32 Then press selection button R. To check the start time: Press selection button 8. To check the stop time: Press selection button 8 again. NOTE: You can not programme the playstimulator over Press selection button R -hold down- and press selection button 0 than release both buttons. Press selection button 3. Service level 3 is reached.
The second time zone has to be filled with zeros. Also this programming is possible: Repeat this procedure until all weekdays are programmed selection buttons 0 to 6. The digital display goes dark.
Enter the new happy hour pricing with 4 digits. To check the new setting, press selection button 7 again. Press selection button 2. Service level 2 is reached. Service level 1 is reached. Press selection button 8, the display shows flashing: 1 means higher digits Then the four higher digits will be displayed. Enter the desired setting with two digits. To check the settings: Press selection button 9 again. Page Data Retrieval Press button 0 again, the display shows the CD with the second lowest number of plays etc.
To cancel the procedure press selection button R. Page 41 The sequence of top LH magazine discs is for the time being 01, 02, 03, 04 etc. With max. Af- ter about one minute the CD is taken back.. If no credits in memory, no CD will be taken to turntable, the display is flashing. Page 46 Preset volume level 60 61 - switch position ON high Page Speaker Connections R.
The preset volume can be set separately. Page Amplifier K99 The output power is designed for the typical used internal speakers at Deutsche Wurlitzer GmbH machines, under normal circumstances reaching an impeccable volume level. No initialisations run after power ON. The status display on the amplifier is dark.
The pots Vol. Page The Infrared Remote Control To open the battery compartment move the cover like shown in the picture. Page External Speaker Connection Note that speaker groups like in hi-fi boxes may have, at certain fre- Terminal R-extern quencies, impedance much lower than their rating. Make sure that all spea- DIP switch 2channel- kers are connected in correct polarity. Page External Amplifier Connection If it is impossible e. Page 70V Output Transformer i. If the power consumption is lower i.
Page Connection Of 70V Systems The primary input- side of this transformer has to be connected in cor- rect polarity with the 70V terminals of the Deutsche Wurlitzer GmbH output transformer. It is not allowed to consume more power than the amplifier is able to supply 23W or 45W , minus the additi- onal speakers eventually connected to the output transformer.
Page Technician Statistics Press selection button 8 once more to display the next error code etc. After displaying the 10th code, special values will be displayed ref to the following chapters.
Exit: Press button R. In this example the total operating time is minutes ap- prox. Page Function Tests Each button operation makes the sledge move one step upwards and the display will be increased by 2.
Last position is If both magazines exist, the left one will be used as reference. If the L. Page 68 The just running step runs to its end.
The machine waits. Only the next one step runs. Press button 5 again etc. Single step - OFF: Press selection button 6. Page 69 CD2 mechanism e. This value adds itself. The RH digit is always 0. Button 3 5 makes the selec- tion sledge move downwards, button 4 6 up- wards. Page 73 Press selection button 3. Here is a short video showing the proper speed of the gripper arm cycle. When the gripper arm motor is too slow it can be either lubrication or a fouled up armature inside the motor itself.
Here are some pictures on fixing the armature by cleaning the gaps with a thin metal strip or plastic that fits snuggly in the slots of the armature. Cleaning these will bring the motor back to factory speed. So if your jukebox is behaving oddly try turning off any compact fluorescent bulbs in the same room and see if the problem goes away Philips originally used a 'Spider' type of centering disc that was prone to breakage of the tiny fingers. This was replaced with a solid cone pdf.
Recommended update! Replacement cone is available here You will need a magnetic puck to keep the CD in place. If you are testing the player in the machine you might want to setup using the self test to clamp a CD. You can order the bulb from us here. With the Safety Switch K8 disengaged the machine will sit forever. Cure: Lift gripper bow up so that the Record Clamp pin clears the Lever, then push the Lever towards the Magazine enough so that when you let the Gripper Bow back down the pin is engaged,and the plastic pin on the Record Clamp pushes against the lever for the Safety Switch Microswitch K8.
I find you can use an old standard digital camera I used a Nikon Coolpix for this test - cell phone cameras filter out IR usually you are able to see on the camera view screen if the laser is lighting up - Infra-Red light.
No light? Check power to player, etc. The picutre on the left shows the laser glowing, the picture on the right shows the laser lighting up a thin peice of paper laid over the lens click on images for bigger pictures. Pressing button 0 once indicates the least popular record. Pressing button 0 again shows the record with second lowest number of plays. Press button 0 again shows the third lowest etc..
Shows the record which was played most frequently followed by the number of plays Max. If one record was played more often than 99 times, the counter remains in this position. Pressing button 1 again shows the second popular record, etc. Shows the cash box contents in basic units; basic units being the value of the lowest coin, resp. All counters are reset to zero. When you press button 4 the digital display automatically indicates the number 8 on all three digits.
The playstimulator is playing a random record automatically after a programmed time period. It is programmable between 1 and 98 minutes.
When you press button 7 relay M should be activated and the changer plays the B-side of the record. Display shows 7 - 4. After the record has been played, it will be returned into the carrier.
When you press button 8 relay M3 is activated and the record carrier turns as long as button 8 is pressed. The gripper arm must be in rest position. The display shows 8 - 0. Press button 9 , test of the gripper arm position. Display shows 9 - 0 if the gripper arm is in rest position, 9 - 1 if the gripper arm is in play position.
0コメント